https://github.com/christophebelmont/Flow.io-Waveshare
Flow.io-Waveshare
TheoIm
Views 132

Comments 0
User Created Content: projects that makers and community members built with WIZnet chips and modules.
5,463 projects
https://github.com/christophebelmont/Flow.io-Waveshare
Flow.io-Waveshare
TheoImViews 132
Comments 0
https://github.com/silly82/esp32poeLarsBatMon
esp32poeLarsBatMon
TheoImViews 89
Comments 0
An Industrial Motor Controller Built with STM32 and W5500 — RS-485 and Ethernet Behind One Register Map
Motor Controller with PID, Modbus RTU and Modbus TCP
scottViews 107
Comments 0
ZigBee Coordinator
ZigBee Coordinator
jadenViews 116
Comments 0
An open KiCad board merges four serial lines into one Ethernet feed on a W55RP20, driving ioLibrary hardware sockets directly with no lwIP in the build.
How Does a Wires-First UART Combiner Move Four Serial Streams Over W55RP20 Ethernet?
AlanViews 148
Comments 0
ESP32-based IMU sensor device for the natKit BCI toolkit. This device collects inertial measurement data and streams it to the natKit backend via MQTT.
natKit-IMU
Lihan__Views 187
Comments 0
Use esp32-s3-poe-eth to connect to Tesla Powerwall AP and proxy requests to ethernet
esp32-wifi-bridge
Lihan__Views 141
Comments 0
UC Berkeley's student rocket team, Space Enterprise at Berkeley (SEB), builds an Automatic Electronic Pressure Regulator (E-Reg)
Automatic Electronic Pressure Regulator
lawrenceViews 121
Comments 0
Weidos doesn't use the W5500 as a plain Ethernet PHY/interface. Its official Ethernet.h-based library talks directly to the W5500's hardware TCP socket (TOE).
WeidmullerSA Weidos-ESP32-package : How Does Weidmüller Weidos Actually Use the W5500's TOE?
lawrenceViews 156
Comments 0
OpenAmber replaces the Itho Amber heat pump controller with an ESP32 running ESPHome; the ESP32-P4 build uses a WIZnet W5500 for wired Home Assistant control.
OpenAmber: Open-Source ESP32 Heat Pump Controller With W5500 Wired Ethernet
ElenaLeeViews 178
Comments 0
ESP32-S3 and W5500 controller that bridges FRC arena WebSocket PLC data to HUB counters, relays, and addressable LEDs.
ESP32-S3 + W5500 FRC Arena HUB Controller
josephsrViews 131
Comments 0
A full-stack access control platform linking STM32 door hardware to MQTT, with optional W5500 Ethernet, Wi-Fi, RFID, fingerprint, and remote control.
STM32 Smart Access Control with Optional W5500 Ethernet
josephsrViews 114
Comments 0
ND-PicoDMX-System pairs a Raspberry Pi Pico with a WIZnet W5500 that receives Art-Net and sACN; dual-core firmware and PIO drive four DMX512 outputs at 40 Hz.
How Does a W5500 Pico Node Drive Four DMX512 Ports from Art-Net and sACN at 40 Hz?
BenjaminViews 110
Comments 0
Ooznest board support in grblHAL/ESP32 routes Telnet, WebSocket, FTP and WebUI over a W5500 SPI Ethernet link on the ESP32-S3, with Wi-Fi compiled alongside.
Why Did CNC Vendor Ooznest Choose W5500 Ethernet for Its grblHAL ESP32-S3 Board?
BenjaminViews 125
Comments 0
Surat factory WiFi is unreliable, so the EaseEmbro MES gives its ESP32-S3 fingerprint terminal a W5500 wired Ethernet option. The platform runs 33 factories.
Why Did EaseEmbro Put a W5500 Wired Option in Its ESP32-S3 Attendance Terminal?
BenjaminViews 98
Comments 0
Native ethernet: config for WIZnet W6100 SPI and W6300 PIO QSPI on RP2040/RP2350, merged by Home Assistant developer bdraco and shipped in ESPHome 2026.4.0.
What Does ESPHome Support for W6100 and W6300 Ethernet Add on RP2040 and RP2350?
BenjaminViews 143
Comments 0
A WIZnet W5500 on the arm's master RP2040 Pico carries TCP and UDP motion commands from the Arduino UNO Q host, using WIZnet's own ioLibrary socket API.
Which Ethernet Chip Connects an Arduino UNO Q to a 6-Axis Robot Arm? The W5500
BenjaminViews 103
Comments 0
A peer-reviewed 2026 paper wires an ESP32, three PZEM-004T sensors, and a W5500 Ethernet module into the BMKG Sleman station LAN to log 3-phase kWh in MySQL.
How Does a W5500 Wired ESP32 Monitor 3-Phase Power at a BMKG Geophysics Station?
BenjaminViews 93
Comments 0
Full hardware TCP/IP stack, eight sockets, a dedicated 32 KB buffer, 80 MHz SPI. UCF Group 21 wrote the comparison down, then measured the chip on its bench.
Why the W5500 Beat the ENC28J60 and AX11001 in a UCF Animatronic Trade Study
BenjaminViews 108
Comments 0
AmeNote ProtoZOA's NetworkMIDI2_Bridge connects USB MIDI 2.0 devices to Network MIDI 2.0 over wired Ethernet using an RP2040 and a WIZnet W5500 expansion board.
How to Bridge Network MIDI 2.0 with W5500 on RP2040?
viktorViews 129
Comments 0
PIXPAPER-213-C is a 2.13-inch, four-color electronic paper display that can be driven from the WIZnet W6300-EVB-Pico2 under Zephyr RTOS
How to Drive a PIXPAPER-213-C Display on W6300-EVB-Pico2 with Zephyr?
viktorViews 105
Comments 0
CRANTROL is an ESP32-S3 and W5500 Ethernet remote control platform with 10-channel relay control, Flutter mobile app, Firebase sync, and captive portal setup.
CRANTROL: W5500-Based IoT Control Platform
irinaViews 127
Comments 0
BASIX is an open-hardware PIC18 controller integrating W5500 Ethernet, RS-485, isolated I/O, analog inputs, relays, EEPROM, and RTC for automation.
BASIX Board with W5500
irinaViews 126
Comments 0
protective-stop
protective-stop
TheoImViews 211
Comments 0
Share projects and connect with makers.
Joined before the site update? first.
New to WIZnet Makers?
We sent a verification link to your address. Open it to activate your account, then log in.
Accounts from this email provider are reviewed by an administrator after verification. Approval usually takes one business day.
Already have an account?
Enter your email address. If it belongs to an account, we'll send a link to set a new password. Members who joined before the site update use this to set their password.
If an account uses that address, we sent a link to set a new password. The link works once and expires in 30 minutes.
Know your password?
Need an account?