RollerShutter_Arduino_MQTT_Home_Assistant
RollerShutter_Arduino_MQTT_Home_Assistant
mason
Views 380

Comments 0
Hardwired TCP/IP Ethernet controller chip with an SPI interface.
1,610 projects, page 18 of 68
RollerShutter_Arduino_MQTT_Home_Assistant
RollerShutter_Arduino_MQTT_Home_Assistant
masonViews 380
Comments 0
ArtGateOne_2
ArtGateOne_2
masonViews 397
Comments 0
ESP32-S3-ETH Devkit에서 ESP-IDF를 활용하여 W5500 기반 Ethernet을 설정하고, 안정적인 유선 네트워크 환경을 구축하는 과정을 다룹니다.
Setting Up W5500 Ethernet on ESP32-S3 Using ESP-IDF
sophiaViews 425
Comments 0
ESP32-shield-module-W5500-RS485
ESP32-shield-module-W5500-RS485
masonViews 427
Comments 0
An ESP32-C6 gateway uses the W5500 to bridge a CAN-based smart home network to an MQTT cloud.
MySmartHouse3
TheoImViews 319
Comments 0
A DIY PoE access panel built on WIZnet W5500 + ESP32-S3, featuring 3D face, vein, and fingerprint auth via ESPHome and Home Assistant.
A PoE Smart Access Panel Powered by W5500 — From 3D Face Recognition to Vein Authentication
Grace_KooViews 615
Comments 0
Open-source KiCad PCB design for a 4-universe ArtNet LED controller with RP2040, W5500, USB-C charging, and JLCPCB assembly support
2040-ArtNode: RP2040 + W5500 ArtNet LED Controller Board
BenjaminViews 585
Comments 0
This project is a hardware design for an autonomous wheeled vehicle main control board built around the STM32 Nucleo F446RE.
How to Add Wired Telemetry and Vehicle I/O Control with W5500 on STM32 Nucleo F446RE?
viktorViews 450
Comments 0
This project is a compact sub-control board for an autonomous wheeled vehicle that uses a Seeed XIAO SAMD21, a WIZnet W5500 Ethernet module
How to Bridge Ethernet Commands to SBUS with W5500 on Seeed XIAO SAMD21?
viktorViews 321
Comments 0
A Managed Industrial Edge Device with W5500-Based Ethernet, an ESP32-linked Wi-Fi path, LTE-M/NB-IoT, and obnizOS
obniz Intelligent Edge Kilo
matthewViews 390
Comments 0
WLED usermod that receives DDP pixel data over W5500 Ethernet while using WiFi for relay control
TheBreeze: W5500 Ethernet DDP Receiver for WLED
BenjaminViews 491
Comments 0
Building a commercial game show venue — need the most reliable microcontroller setup for buzzers + LEDs +Ethernet
Building a commercial game show venue — need the most reliable microcontroller setup for buzzers + L
gunnViews 307
Comments 0
Akihabara Robot Pedestrian Paradise
秋葉原ロボットほこ天
gunnViews 297
Comments 0
This utility model packages protection, power-quality monitoring, line-loss analysis, and mixed wired/wireless links into a modular field unit built for service
Modular Distribution Protection Controller with WIZnet W5500 and Multi-Role Expansion
josephsrViews 370
Comments 0
DOMIX — Open Source Modular Home Automation System
DOMIX — Open Source Modular Home Automation System
Aimee0Views 421
Comments 0
RoboRacing uses W5500 Ethernet on Arduino boards for TCP/UDP control across an autonomous racing car.
roboracing-firmware
TheoImViews 352
Comments 0
ESP32 Poly-Phase Power Meter
ESP32 Poly-Phase Power Meter
scottViews 455
Comments 0
This ESP32 project monitors DS18B20 temperature sensors across two OneWire buses and sends readings to an external server through a W5500 Ethernet interface
How to Monitor DS18B20 Sensors with W5500 on ESP32?
viktorViews 398
Comments 0
Batear is an open-source acoustic drone detection system using ESP32-S3, MEMS mic, and LoRa or wired Ethernet/PoE.
Batear
Aimee0Views 559
Comments 0
QuSpin Magpie: Field-Ready Total-Field Magnetometer Platform with ESP32 Wireless Control and Optional W5500 Ethernet
MAGPIE
matthewViews 546
Comments 0
Ayatec Sensoraya v2.1 is a configurable DIN-rail I/O controller built around the ESP32-S3, with the WIZnet W5500 used as the wired Ethernet interface
How to Build a DIN-Rail ESP32-S3 Controller with W5500 for Industrial Automation?
viktorViews 630
Comments 0
ESP32-S3 + W5500 Ethernet escape room telephone prop. Decodes rotary/DTMF dialing, plays audio via ProSLIC FXS, connects to MQTT. PoE or barrel jack
Phone Prop Controller — ESP32-S3 + W5500 Escape Room Telephone with MQTT & ProSLIC
irinaViews 318
Comments 0
Open-source ESP32-S3 6-axis CNC motion controller. WiFi or W5500 Ethernet auto-detected. LinuxCNC, GRBL, Mach3 support. TCP+UDP real-time protocol.
Tiggy_Wifi_Controller
irinaViews 345
Comments 0
Test run using ESP32 + WIZnet W5500 implementing MODBUS over Ethernet with DHCP and TCP/IP via PlatformIO and Arduino framework.
MODBUS over Ethernet with ESP32 & W5500 – TCP/IP + DHCP Test Run
irinaViews 765
Comments 0
Share projects and connect with makers.
Joined before the site update? first.
New to WIZnet Makers?
We sent a verification link to your address. Open it to activate your account, then log in.
Accounts from this email provider are reviewed by an administrator after verification. Approval usually takes one business day.
Already have an account?
Enter your email address. If it belongs to an account, we'll send a link to set a new password. Members who joined before the site update use this to set their password.
If an account uses that address, we sent a link to set a new password. The link works once and expires in 30 minutes.
Know your password?
Need an account?