ESP-Miner NerdQAxePlus V3.4 - TNA Edition LAN and OVERCLOCKING READY
ESP-Miner NerdQAxePlus V3.4 - TNA Edition LAN and OVERCLOCKING READY
scott
Views 314

Comments 0
User Created Content: projects that makers and community members built with WIZnet chips and modules.
2,084 projects
ESP-Miner NerdQAxePlus V3.4 - TNA Edition LAN and OVERCLOCKING READY
ESP-Miner NerdQAxePlus V3.4 - TNA Edition LAN and OVERCLOCKING READY
scottViews 314
Comments 0
An STM32F103-powered dev board in an Arduino UNO form factor
ARMduino
Sunny_Views 220
Comments 0
grass-valley-gpio-controller
grass-valley-gpio-controller
Aimee0Views 212
Comments 0
MCM_GitHub_OTA Library
MCM_GitHub_OTA Library
scottViews 353
Comments 0
Filla IQ
Filla IQ
Aimee0Views 355
Comments 0
RIT Launch Initiative OTIS project
RIT Launch Initiative OTIS project
Aimee0Views 228
Comments 0
Open-source Drone-in-a-Box system that links Home Assistant alarms with MAVLink drones for automated patrols, live monitoring, and secure dock control.
drone_hass
Aimee0Views 234
Comments 0
no_std Rust library implementing Blackmagic ATEM UDP/BURP protocol for Embassy-based embedded systems. Enables MCUs with W5500 Ethernet to control professional
edge bmd atem
Lihan__Views 387
Comments 0
Building Room-Level Presence Detection with a Wi-Fi-Independent BLE Scanner: PadSpan HA with ESP32-S3 + W5500
padspanHA
Aimee0Views 260
Comments 0
W5500 Ethernet for Sharp X68000 (1987) via joystick port bit-banged SPI. inetd.x-compatible TCP/IP driver enables SMB, HTTPS, web browsing on vintage hardware.
joynetd
Lihan__Views 311
Comments 0
aily-blockly-libraries
aily-blockly-libraries
Aimee0Views 239
Comments 0
A handheld ESP32-S3 diagnostic tool that captures LLDP frames over W5500 Ethernet, parses neighbor and VLAN data, and displays it with touch-driven ping tests.
ESP32-S3 LLDP Monitor with W5500 Ethernet, Touch UI, and On-Device Ping
josephsrViews 348
Comments 0
CNC firmware optimized for the ESP32 controller. It is the next generation of firmware from the creators of Grbl_ESP32. It includes a web based UI and the flex
FluidNC
Sunny_Views 223
Comments 0
This project is a reliable, Arduino-based controller for Endless Pools swimming machines, offering a modern web interface for seamless control and workout manag
Endless Pools Controller (ESP32-S3)
Sunny_Views 212
Comments 0
ROR_Controller
ROR_Controller
masonViews 318
Comments 0
tinyplayer
tinyplayer
masonViews 280
Comments 0
RollerShutter_Arduino_MQTT_Home_Assistant
RollerShutter_Arduino_MQTT_Home_Assistant
masonViews 325
Comments 0
ArtGateOne_2
ArtGateOne_2
masonViews 347
Comments 0
ESP32-S3-ETH Devkit에서 ESP-IDF를 활용하여 W5500 기반 Ethernet을 설정하고, 안정적인 유선 네트워크 환경을 구축하는 과정을 다룹니다.
Setting Up W5500 Ethernet on ESP32-S3 Using ESP-IDF
sophiaViews 363
Comments 0
ESP32-shield-module-W5500-RS485
ESP32-shield-module-W5500-RS485
masonViews 394
Comments 0
An STM32 and W5500 Ethernet controller for solar DC bus monitoring, distributed water-heater control, MPPT load management, and energy data logging.
xugongke Solar energy
matthewViews 207
Comments 0
A configurable MCU platform simulates incremental and SSI encoder outputs, injects faults, and converts them into industrial differential signals for PLC test.
Microcontroller-Based Encoder Signal Emulator for PLC Interface Testing
josephsrViews 307
Comments 0
A Zephyr RTOS driver PR for WIZnet W6300 on RP2350, using bit-bang SPI + MACRAW mode. Currently under review.
W6300 Zephyr Driver PR #102727: Under Review
Grace_KooViews 280
Comments 0
An ESP32-S3 CCTV/IoT firmware combining W5500 Ethernet, motion detection, SD recording, MQTT, and a web UI for wired LAN camera nodes.
ESP32-S3 CCTV Camera — IoT Surveillance Camera Firmware with W5500 Ethernet Support
matthewViews 275
Comments 0
Share projects and connect with makers.
Joined before the site update? first.
New to WIZnet Makers?
We sent a verification link to your address. Open it to activate your account, then log in.
Accounts from this email provider are reviewed by an administrator after verification. Approval usually takes one business day.
Already have an account?
Enter your email address. If it belongs to an account, we'll send a link to set a new password. Members who joined before the site update use this to set their password.
If an account uses that address, we sent a link to set a new password. The link works once and expires in 30 minutes.
Know your password?
Need an account?