How to Add Wired Ethernet with WIZnet W5500 on Wio Terminal Using Arduino?
The Seeed Studio Wio Terminal can be extended with wired Ethernet connectivity using the WIZnet W5500 hardware TCP/IP controller and the Arduino development env
0
Project description
How to Add Wired Ethernet with WIZnet W5500 on Wio Terminal Using Arduino?
Platform: Seeed Studio Wio Terminal | Ethernet Controller: WIZnet W5500 | Development Environment: Arduino IDE | Application: Maker Projects
1. Summary
The Seeed Studio Wio Terminal can be extended with wired Ethernet connectivity using the WIZnet W5500 hardware TCP/IP controller and the Arduino development environment. The W5500 connects to the Wio Terminal's ATSAMD51 microcontroller over SPI and handles TCP/IP networking operations through dedicated hardware sockets. This architecture allows makers to develop Ethernet-connected dashboards, local web servers, and sensor monitoring devices while reducing the microcontroller resources required for network protocol processing.
The original CSDN article describes the proposed hardware connection and explains why the W5500 is preferable to a software TCP/IP implementation for certain embedded applications. However, the accessible article does not provide a complete, independently verifiable Arduino firmware implementation or test results.
blog.csdn.net+2
2. What the Project Does
The project explores how to add wired Ethernet networking to the Wio Terminal, an Arduino-compatible development board based on the Microchip ATSAMD51P19 microcontroller.
The Wio Terminal includes a 2.4-inch LCD, user buttons, onboard sensors, Grove connectors, and an RTL8720DN wireless communication module. Although it supports Wi-Fi and Bluetooth, it does not include an onboard wired Ethernet controller.
Seeed Studio Wiki+1
For maker applications, external Ethernet enables projects such as a small HTTP server displaying sensor readings, a network-connected control panel, or a desk-mounted monitoring terminal.
Proposed system architecture
Wio Terminal — ATSAMD51
Arduino application, sensor acquisition, LCD interface
SPI: SCK / MOSI / MISO / CS
WIZnet W5500
Hardware TCP/IP, socket management, TX/RX buffers, Ethernet MAC/PHY
RJ45 Ethernet cable
Local Network
Ethernet switch / router → PC or local server
In a proposed sensor-monitoring implementation, the data flow is straightforward: the Wio Terminal reads sensor values, formats them into application messages, and sends the data through the W5500 to a local server. Incoming requests can be processed by the Arduino application and displayed on the screen.
The original article discusses this application category but does not demonstrate a completed sensor-to-server deployment.
3. Where WIZnet Fits
The WIZnet W5500 provides the hardware networking layer between the Wio Terminal and a wired Ethernet network.
Unlike a conventional Ethernet MAC/PHY controller, the W5500 includes hardware logic for TCP/IP communication. Its built-in network functionality allows the MCU to interact with network sockets without independently implementing the full TCP/IP stack.
WIZnet Document System+1
Hardware sockets
8
Internal TX/RX memory
32 KB
SPI maximum
80 MHz
Ethernet PHY
10/100
W5500 chip capabilities. Actual SPI speed, throughput, and socket availability depend on the board, library, configuration, and application.
WIZnet Document System+1
Why hardware TCP/IP offloading matters
The Wio Terminal has 192 KB of SRAM and also handles application tasks such as display updates, user input, and sensor acquisition. A software TCP/IP stack requires additional RAM and CPU time to manage packet processing, connection state, and retransmission behavior.
The W5500 moves supported TCP/IP operations into dedicated hardware. The MCU still handles socket operations through SPI and remains responsible for application-level protocols such as HTTP or MQTT.
This division is useful when developing small embedded interfaces that must continue processing local inputs while maintaining network communication.
The trade-off is less flexibility than a general-purpose software stack. The W5500 is primarily an IPv4 controller and has fixed hardware socket and buffer resources.
4. Implementation Notes
Hardware interface
The original article proposes connecting the W5500 through the Wio Terminal's exposed SPI interface, along with a selectable GPIO for chip select.
| W5500 signal | Connection |
|---|---|
| SCK | Wio Terminal SPI clock |
| MOSI | Wio Terminal SPI data output |
| MISO | Wio Terminal SPI data input |
| CS | Available GPIO, active low |
| RST | Optional GPIO for hardware reset |
| INT | Optional GPIO for W5500 interrupts |
| VCC | Module-specified supply |
| GND | Common ground |
The article suggests Arduino pin identifiers D24, D23, and D22 for SPI signals, and D10 for CS. These assignments have not been confirmed against a working Wio Terminal/W5500 hardware combination. The actual pin mapping should be checked against the board variant and adapter documentation before wiring.
The W5500 chip operates at 3.3 V, but assembled Ethernet modules may include voltage regulators or level-shifting circuitry. Supply the module according to its own specifications rather than assuming that all W5500 boards have identical power inputs.
Arduino firmware architecture
A practical firmware design can be divided into four stages.
Initialize the SPI interface
Configure the board's SPI peripheral and the GPIO controlling W5500 chip select. Verify that other SPI devices are not selected during Ethernet transactions.
Initialize the Ethernet controller
Use a W5500-compatible Arduino Ethernet library, configure chip select, and initialize the controller after power-up or hardware reset.
Establish network configuration
Obtain an IPv4 address using DHCP or configure a static address, subnet mask, gateway, and DNS server as required by the application.
Run the application network loop
Open a TCP or UDP socket, exchange data with the intended endpoint, manage disconnections and timeouts, and continue updating sensors or the LCD.
This implementation sequence is an architectural recommendation, not a confirmed reproduction of the CSDN author's firmware. No downloadable source repository, verified .ino file, or complete working W5500 initialization routine could be established from the accessible material.
Arduino libraries and API selection
Two different software paths are relevant to Wio Terminal Ethernet projects:
| Library | Ethernet hardware | TCP/IP processing |
|---|---|---|
| Arduino Ethernet library with W5500 support | WIZnet W5500 | Hardware offload |
| UIPEthernet | ENC28J60 | Software stack on MCU |
Seeed Studio provides a Wio Terminal Ethernet example using an ENC28J60 board and UIPEthernet. That example is useful as a reference for Wio Terminal networking, but it is not evidence of a working W5500 firmware port.
Seeed Studio Wiki+1
For a W5500 build, the Arduino Ethernet API offers a reasonable implementation direction. The firmware should establish the Ethernet connection, confirm network configuration, and then implement either an Ethernet client or server according to the device's function.
A maker-oriented verification sequence would first confirm that the board receives a valid IP address, then connect to a local HTTP service, and finally integrate sensors and LCD rendering. This separates hardware communication problems from higher-level application problems.
5. Practical Tips / Pitfalls
Confirm SPI pin mapping: Wio Terminal pin identifiers and Raspberry Pi-style expansion-header pin numbers are not interchangeable. Verify the exact board core and adapter before wiring.
Check module power requirements: The W5500 chip is a 3.3 V device. Inspect the selected module's regulator and signal-level specifications before connecting power.
Test Ethernet link before DHCP: A correctly initialized W5500 cannot obtain an address when the physical link is disconnected. Check RJ45 link LEDs and PHY status.
Use a known network configuration: Start with DHCP on a local router. If address assignment fails, use a valid static IPv4 configuration to separate DHCP issues from SPI and PHY problems.
Manage socket and buffer limits: The W5500 supports eight hardware sockets sharing 32 KB of internal TX/RX memory. Avoid assuming that every socket can provide maximum buffering simultaneously.
Implement connection recovery: Include socket timeouts, link checks, and reconnection logic. For longer-running maker projects, add a watchdog strategy that accounts for legitimate network delays.
Reduce electrical noise: Keep SPI wiring short, maintain solid ground connections, and avoid routing high-speed signals next to motors or switching power cables.
6. FAQ
Q1. Why use WIZnet W5500 instead of a software TCP/IP stack on Wio Terminal?
The W5500 handles supported TCP/IP operations in hardware and provides eight independent sockets with internal packet buffers. This reduces the amount of TCP/IP protocol processing required from the ATSAMD51, leaving more of its resources available for Arduino application logic, sensors, and graphics.
Q2. How does the W5500 connect to the Wio Terminal?
The controller communicates over SPI using SCK, MOSI, MISO, and an active-low chip-select signal. Optional connections include reset and interrupt GPIOs. Exact Wio Terminal pin assignments must be verified for the selected expansion hardware.
Q3. What does the W5500 actually do in this project?
The W5500 provides the wired IPv4 networking interface. It handles supported TCP/IP transport operations and packet buffering, while the Wio Terminal executes the application, processes sensor readings, renders the LCD, and produces or consumes application-level messages.
Q4. Can Arduino beginners build a Wio Terminal Ethernet project with W5500?
Yes, provided they have basic experience uploading Arduino sketches, connecting SPI devices, and configuring IP networks. A sensible progression is to verify SPI communication and Ethernet link status, obtain a DHCP address, and then implement a simple TCP client or HTTP server. The original article should be treated as design guidance rather than a fully tested beginner tutorial.
Q5. How does the W5500 compare with Wi-Fi and ENC28J60?
The W5500 uses wired Ethernet and offloads supported TCP/IP operations. Wio Terminal's built-in Wi-Fi avoids additional wiring and is better suited to portable applications, but wireless connectivity can be affected by interference, access-point availability, and network configuration.
The ENC28J60 also provides wired Ethernet, but it does not contain the W5500's hardware TCP/IP engine. Its host MCU must run a software network stack such as the one used by UIPEthernet.
| Criterion | W5500 | Built-in Wi-Fi | ENC28J60 |
|---|---|---|---|
| Medium | Wired | Wireless | Wired |
| TCP/IP processing | W5500 hardware | Wireless subsystem/firmware | MCU software |
| External Ethernet module | Required | Not required | Required |
| Physical connection | SPI + RJ45 | Radio | SPI + RJ45 |
| Main trade-off | Additional wiring, limited hardware sockets | Wireless environment dependence | MCU software-stack overhead |
For a fixed desktop maker project requiring wired connectivity and relatively simple TCP/UDP communication, the W5500 offers a useful separation between network transport and application logic. It does not inherently guarantee real-time latency or eliminate application-level networking errors.
7. Source
Original article: Wio Terminal Ethernet Connection: W5500 Hardware TCP/IP Stack and Arduino Network Programming
Author: 爱浪的刀
Publication date: August 1, 2026
License: CC BY-SA 4.0, as declared in the supplied article text.
Technical references:
The original article establishes W5500 as the proposed Ethernet controller. Its accessible contents describe hardware selection and SPI connections, but a corresponding tested firmware repository, specific working code, and reproducible performance measurements were not available. This article therefore separates source-supported technical descriptions from recommended implementation steps.
8. Tags
#W5500 #WIZnet #WioTerminal #Arduino #Ethernet #SPI #TCPIP #MakerProjects #EmbeddedSystems #IoT
Arduino를 이용해 Wio Terminal에 WIZnet W5500 유선 이더넷을 연결하는 방법은?
플랫폼: Seeed Studio Wio Terminal | 이더넷 컨트롤러: WIZnet W5500 | 개발 환경: Arduino IDE | 활용 분야: 메이커 프로젝트
1. 프로젝트 개요
Seeed Studio Wio Terminal은 WIZnet W5500 하드웨어 TCP/IP 컨트롤러와 Arduino 개발 환경을 활용해 유선 이더넷 연결 기능을 확장할 수 있다. W5500은 Wio Terminal의 ATSAMD51 마이크로컨트롤러와 SPI 인터페이스로 연결되며, 전용 하드웨어 소켓을 통해 TCP/IP 네트워크 통신을 처리한다. 이 구조를 활용하면 MCU의 네트워크 프로토콜 처리 부담을 줄이면서 이더넷 기반 대시보드, 로컬 웹 서버, 센서 모니터링 장치 등을 개발할 수 있다.
원본 CSDN 문서는 W5500의 하드웨어 연결 방식과 소프트웨어 TCP/IP 방식 대비 기술적 장점을 설명한다. 다만 확인 가능한 자료에는 완성된 Arduino 펌웨어 구현이나 독립적으로 검증된 테스트 결과가 포함되어 있지 않다.
2. 프로젝트의 주요 기능
이 프로젝트는 Microchip ATSAMD51P19 마이크로컨트롤러 기반의 Arduino 호환 개발 보드인 Wio Terminal에 유선 이더넷 연결 기능을 추가하는 방법을 다룬다.
Wio Terminal에는 2.4인치 LCD, 사용자 입력 버튼, 내장 센서, Grove 커넥터, RTL8720DN 무선 통신 모듈이 탑재되어 있다. Wi-Fi와 Bluetooth는 지원하지만 유선 이더넷 컨트롤러는 기본적으로 제공하지 않는다.
외부 이더넷 컨트롤러를 연결하면 다음과 같은 메이커 프로젝트를 구현할 수 있다.
센서 측정값을 웹 브라우저에 표시하는 HTTP 서버
로컬 네트워크에서 데이터를 송수신하는 제어 패널
네트워크 연결 상태와 센서 데이터를 표시하는 데스크톱 모니터링 장치
Ethernet 기반 TCP/UDP 통신 실습 프로젝트
시스템 구성
Wio Terminal — ATSAMD51
Arduino 애플리케이션, 센서 데이터 수집, LCD 화면 처리
SPI: SCK / MOSI / MISO / CS
WIZnet W5500
하드웨어 TCP/IP, 소켓 관리, 송수신 버퍼, Ethernet MAC/PHY
RJ45 이더넷 케이블
로컬 네트워크
이더넷 스위치 / 라우터 → PC 또는 로컬 서버
센서 모니터링 장치를 예로 들면, Wio Terminal이 센서 데이터를 수집한 후 이를 애플리케이션 메시지로 변환하고 W5500을 통해 로컬 서버에 전송하는 구조다.
서버로부터 수신한 요청이나 응답은 Arduino 애플리케이션에서 처리할 수 있으며, 필요한 정보는 Wio Terminal의 LCD 화면에 표시할 수 있다.
원본 문서는 이러한 활용 가능성을 소개하지만, 실제 센서 데이터가 서버까지 전송되는 완성된 구현을 입증하지는 않는다.
3. WIZnet W5500의 역할
WIZnet W5500은 Wio Terminal과 유선 이더넷 네트워크 사이에서 하드웨어 네트워크 통신을 담당한다.
일반적인 Ethernet MAC/PHY 컨트롤러와 달리 W5500은 TCP/IP 프로토콜 처리 기능을 하드웨어에 내장하고 있다. 따라서 MCU가 모든 TCP/IP 프로토콜 처리를 소프트웨어로 수행할 필요 없이 SPI를 통해 W5500의 소켓 기능을 사용할 수 있다.
하드웨어 소켓
8개
내부 TX/RX 메모리
32 KB
최대 SPI 클록
80 MHz
Ethernet PHY
10/100
W5500 칩의 하드웨어 사양이다. 실제 SPI 동작 속도, 통신 처리량, 사용 가능한 소켓 수는 개발 보드와 라이브러리, 설정 및 애플리케이션에 따라 달라질 수 있다.
하드웨어 TCP/IP 오프로딩이 중요한 이유
Wio Terminal은 192 KB SRAM을 사용하며, 네트워크 통신 외에도 LCD 화면 갱신, 버튼 입력 처리, 센서 데이터 수집 등의 작업을 수행한다.
소프트웨어 TCP/IP 스택을 사용할 경우 다음 기능을 처리하기 위해 MCU의 메모리와 연산 자원이 추가로 사용된다.
패킷 처리 및 프로토콜 상태 관리
TCP 연결 관리
데이터 재전송
송수신 버퍼 관리
W5500은 지원되는 TCP/IP 처리 기능을 전용 하드웨어에서 수행한다. 그 결과 ATSAMD51은 애플리케이션 로직에 더 많은 자원을 사용할 수 있다.
단, MCU가 네트워크 처리에서 완전히 벗어나는 것은 아니다. SPI 통신과 소켓 API 호출, HTTP나 MQTT 같은 애플리케이션 계층 프로토콜 처리는 여전히 펌웨어가 담당한다.
또한 W5500은 기본적으로 IPv4 중심의 컨트롤러이며, 하드웨어 소켓 수와 내부 버퍼 용량에 제한이 있다.
4. 구현 방법
4.1 하드웨어 연결
원본 문서는 Wio Terminal의 SPI 인터페이스를 통해 W5500을 연결하는 방식을 제안한다.
| W5500 신호 | 연결 방식 |
|---|---|
| SCK | Wio Terminal SPI 클록 |
| MOSI | Wio Terminal SPI 데이터 출력 |
| MISO | Wio Terminal SPI 데이터 입력 |
| CS | 사용 가능한 GPIO, Active Low |
| RST | 선택 사항, 하드웨어 리셋용 GPIO |
| INT | 선택 사항, W5500 인터럽트용 GPIO |
| VCC | 모듈 사양에 맞는 전원 |
| GND | 공통 GND |
원본에서는 SPI 신호에 대해 D24, D23, D22를, CS에는 D10을 사용하는 예시를 제시한다.
그러나 이 핀 배치는 실제 Wio Terminal과 W5500 조합에서 검증된 것으로 확인되지 않았다.
실제 연결 전에는 사용하는 Wio Terminal 보드 패키지와 확장 보드의 핀 매핑을 확인해야 한다.
W5500 칩 자체는 3.3 V 전원을 사용하지만, 완제품 이더넷 모듈은 별도의 전압 레귤레이터나 레벨 변환 회로를 포함할 수 있다. 따라서 모듈별 전원 사양을 기준으로 연결해야 한다.
4.2 Arduino 펌웨어 구성
Arduino 펌웨어는 크게 네 단계로 구성할 수 있다.
SPI 인터페이스 초기화
Wio Terminal의 SPI 주변장치를 설정하고, W5500의 Chip Select 신호를 제어하는 GPIO를 초기화한다. 다른 SPI 장치와 버스를 공유하는 경우 동시 선택이 발생하지 않도록 관리한다.
W5500 이더넷 컨트롤러 초기화
W5500을 지원하는 Arduino Ethernet 라이브러리를 사용한다. CS 핀을 설정하고, 전원 인가 또는 하드웨어 리셋 이후 컨트롤러 초기화를 수행한다.
네트워크 설정
DHCP로 IPv4 주소를 할당받거나, 애플리케이션 요구사항에 따라 고정 IP 주소, 서브넷 마스크, 게이트웨이, DNS 서버를 설정한다.
네트워크 애플리케이션 실행
TCP 또는 UDP 소켓을 열어 데이터를 송수신한다. 연결 해제와 타임아웃을 처리하면서 센서 데이터 수집이나 LCD 갱신 작업도 계속 수행한다.
위 단계는 Arduino 기반 W5500 시스템을 설계하기 위한 권장 구현 구조이며, 원본 작성자의 실제 펌웨어를 재현한 내용은 아니다.
확인 가능한 자료에서는 다운로드 가능한 소스 저장소, 완성된 .ino 파일, 실제 동작이 검증된 W5500 초기화 코드를 확인할 수 없었다.
4.3 Arduino 라이브러리 선택
Wio Terminal에서 이더넷을 구성할 때는 W5500과 ENC28J60의 소프트웨어 처리 방식 차이를 이해해야 한다.
| 라이브러리 | 이더넷 하드웨어 | TCP/IP 처리 |
|---|---|---|
| Arduino Ethernet 라이브러리 | WIZnet W5500 | 하드웨어 오프로딩 |
| UIPEthernet | ENC28J60 | MCU 소프트웨어 스택 |
Seeed Studio는 ENC28J60과 UIPEthernet을 활용하는 Wio Terminal Ethernet 예제를 제공한다.
이 예제는 Wio Terminal의 네트워크 프로그래밍을 이해하는 데 참고할 수 있지만, W5500 펌웨어가 정상 동작한다는 직접적인 근거는 아니다.
W5500 기반 구현에서는 Arduino Ethernet API를 활용하는 방식이 적절한 출발점이다.
초기 개발 단계에서는 다음 순서로 기능을 검증하는 것이 좋다.
1단계: SPI 통신 및 이더넷 링크 확인
2단계: DHCP를 통한 IP 주소 할당 확인
3단계: 로컬 HTTP 서버와 TCP 통신 확인
4단계: 센서 데이터 및 LCD 화면 기능 통합
이처럼 하드웨어 통신과 네트워크 기능을 먼저 검증하면, 이후 애플리케이션에서 문제가 발생했을 때 원인을 구분하기 쉽다.
5. 실전 구현 팁과 주의사항
SPI 핀 매핑 확인: Wio Terminal의 Arduino 핀 번호와 확장 커넥터의 물리적 핀 번호는 구분해야 한다. 사용하는 보드와 어댑터의 공식 핀맵을 확인한다.
전원 사양 확인: W5500 칩은 3.3 V 장치다. 모듈의 전원 레귤레이터와 신호 전압 지원 범위를 확인한 후 연결한다.
DHCP보다 물리적 링크를 먼저 확인: 이더넷 링크가 연결되지 않았다면 W5500 초기화가 성공해도 IP 주소를 정상적으로 할당받을 수 없다. RJ45 LED와 PHY 링크 상태를 확인한다.
네트워크 설정 분리 테스트: 먼저 로컬 라우터에서 DHCP를 시도하고, 문제가 있다면 올바른 고정 IP 설정으로 DHCP 문제와 SPI/PHY 문제를 구분한다.
소켓과 버퍼 관리: W5500은 최대 8개의 하드웨어 소켓과 총 32 KB의 내부 송수신 메모리를 사용한다. 모든 소켓이 최대 버퍼 용량을 동시에 사용할 수 있는 것은 아니다.
연결 복구 로직 구현: 네트워크 타임아웃, 링크 상태 확인, 연결 재시도 로직을 구현한다. 장시간 실행하는 프로젝트에서는 정상적인 네트워크 지연을 고려한 Watchdog도 사용할 수 있다.
전기적 노이즈 관리: SPI 배선은 짧게 유지하고 접지를 안정적으로 구성한다. 모터나 스위칭 전원 근처에 고속 신호선을 배치하지 않는 것이 좋다.
6. FAQ
Q1. Wio Terminal에서 소프트웨어 TCP/IP 스택 대신 WIZnet W5500을 사용하는 이유는 무엇인가요?
W5500은 TCP/IP 프로토콜 처리 기능을 하드웨어에 내장하고 있으며, 8개의 독립적인 하드웨어 소켓과 내부 패킷 버퍼를 제공한다.
이를 통해 ATSAMD51이 수행해야 하는 TCP/IP 프로토콜 처리 작업을 줄일 수 있다. MCU는 Arduino 애플리케이션, 센서 처리, LCD 그래픽 등의 기능에 더 많은 자원을 활용할 수 있다.
Q2. W5500은 Wio Terminal에 어떻게 연결하나요?
W5500은 SPI 인터페이스를 이용한다. SCK, MOSI, MISO, CS 신호가 기본적으로 필요하며, 선택적으로 RST와 INT를 연결할 수 있다.
정확한 GPIO 핀 번호는 사용하는 Wio Terminal 확장 하드웨어와 Arduino 보드 설정을 기준으로 확인해야 한다.
Q3. 이 프로젝트에서 W5500은 구체적으로 어떤 역할을 하나요?
W5500은 Wio Terminal의 유선 IPv4 네트워크 인터페이스로 동작한다.
지원되는 TCP/IP 통신 처리와 패킷 버퍼 관리를 담당하며, Wio Terminal은 센서 데이터 수집, LCD 화면 출력, 애플리케이션 메시지 생성 및 처리를 담당한다.
Q4. Arduino 초보자도 W5500 기반 Wio Terminal 프로젝트를 구현할 수 있나요?
Arduino 스케치 업로드, 기본 SPI 배선, IP 네트워크 설정에 대한 기초 지식이 있다면 구현할 수 있다.
처음에는 SPI 통신과 이더넷 링크 상태를 확인하고, 이후 DHCP 주소 할당과 간단한 TCP 클라이언트 또는 HTTP 서버를 구현하는 순서가 적절하다.
다만 원본 문서는 검증된 전체 펌웨어 튜토리얼이라기보다 하드웨어 선택과 설계 방향에 대한 참고 자료로 활용하는 것이 좋다.
Q5. W5500은 Wi-Fi 및 ENC28J60과 어떤 차이가 있나요?
W5500은 유선 이더넷을 사용하며 TCP/IP 프로토콜 처리 기능을 하드웨어에 내장하고 있다.
Wio Terminal의 내장 Wi-Fi는 추가 배선이 필요하지 않아 이동형 프로젝트에 적합하지만, 무선 간섭이나 액세스 포인트 상태에 따라 연결 품질이 달라질 수 있다.
ENC28J60 역시 유선 이더넷 연결을 제공하지만 W5500과 같은 하드웨어 TCP/IP 엔진이 없으므로 MCU에서 소프트웨어 TCP/IP 스택을 실행해야 한다.
| 비교 항목 | W5500 | 내장 Wi-Fi | ENC28J60 |
|---|---|---|---|
| 연결 방식 | 유선 | 무선 | 유선 |
| TCP/IP 처리 | W5500 하드웨어 | 무선 통신 모듈/펌웨어 | MCU 소프트웨어 |
| 외부 Ethernet 모듈 | 필요 | 불필요 | 필요 |
| 물리적 연결 | SPI + RJ45 | 무선 RF | SPI + RJ45 |
| 주요 고려사항 | 별도 배선, 소켓 수 제한 | 무선 환경 의존성 | MCU의 프로토콜 처리 부담 |
고정된 위치에서 동작하면서 비교적 단순한 TCP/UDP 통신이 필요한 메이커 프로젝트라면, W5500은 네트워크 전송 처리와 애플리케이션 로직을 분리할 수 있는 유용한 선택지다.
다만 W5500을 사용한다고 해서 실시간 지연시간이 무조건 보장되거나 모든 네트워크 오류가 제거되는 것은 아니다.
7. 참고 자료
원본 문서: Wio Terminal 이더넷 연결 실습: W5500 하드웨어 프로토콜 스택과 Arduino 네트워크 프로그래밍
원작자: 爱浪的刀
게시일: 2026년 8월 1일
라이선스: CC BY-SA 4.0 (제공된 원문에 표시된 라이선스 기준)
기술 참고 문서:
원본 문서는 W5500을 유선 이더넷 구현을 위한 컨트롤러로 제안하며, 하드웨어 선정과 SPI 연결 방식을 설명한다.
다만 실제 동작이 검증된 펌웨어 저장소, 재현 가능한 성능 측정 결과, 완성된 애플리케이션 코드는 확인되지 않았다. 따라서 이 문서에서는 원본에서 확인되는 기술 내용과 추가 구현을 위한 권장 사항을 구분했다.
8. 태그
#W5500 #WIZnet #WioTerminal #Arduino #Ethernet #SPI #TCPIP #MakerProjects #EmbeddedSystems #IoT