W5500 interface with TI

Question

I implement version read command is working and I get 0x04. but i try to ping from my system mi not getting ping response. please look into the configurations. and please let me know if there is something wrongs. void WInzip_init() { // Read_adddress = ((Uint32)(0x00000039) << 8) | Read_OPCODE; // IINCHIP_READ_add_data(Read_adddress); // Write_adddress = ((Uint32)IP_adddress << 8) | Write_OPCODE; // IINCHIP_WRITE_BUF_data(Write_adddress,0x00,10); // // Read_adddress = ((Uint32)IP_adddress << 8) | Read_OPCODE; // 0x00 is the control phase bit sets // IINCHIP_READ_Buf_data(Read_adddress,&read_data[0],10); // comman registers Write_adddress = ((Uint32)Base_address << 8) | Write_OPCODE; IINCHIP_WRITE_add_data(Write_adddress , MR_R); // Read_adddress = ((Uint32)Base_address << 8) | Read_OPCODE; // IINCHIP_READ_add_data(Read_adddress); Write_adddress = ((Uint32)Getway_address << 8) | Write_OPCODE; IINCHIP_WRITE_BUF_data(Write_adddress,&winzip_config_gatway_subnet[0],8); Write_adddress = ((Uint32)Mac_address << 8) | Write_OPCODE; IINCHIP_WRITE_BUF_data(Write_adddress,&mac[0],6); Write_adddress = ((Uint32)IP_address << 8) | Write_OPCODE; IINCHIP_WRITE_BUF_data(Write_adddress,&Source_IP[0],4); Write_adddress = ((Uint32)PHY_address << 8) | Write_OPCODE; IINCHIP_WRITE_add_data(Write_adddress , PHY_register); Read_adddress = ((Uint32)Base_address << 8) | Read_OPCODE; // 0x00 is the control phase bit sets IINCHIP_READ_Buf_data(Read_adddress,&read_data[0],20); //Socket Registers Settings// Write_adddress = ((Uint32)Base_address << 8) | Write_Socket_OPCODE; // tcp 0x01 IINCHIP_WRITE_add_data(Write_adddress , Sn_MR); Write_adddress = ((Uint32)Port_adddress << 8) | Write_Socket_OPCODE; // port 5000 IINCHIP_WRITE_BUF_data(Write_adddress,&Port[0],2); // Read_adddress = ((Uint32)Port_adddress << 8) | Read_Socket_OPCODE; // 0x00 is the control phase bit sets // IINCHIP_READ_Buf_data(Read_adddress,&read_data[0],2); Read_adddress = ((Uint32)Base_address << 8) | Read_Socket_OPCODE; IINCHIP_READ_add_data(Read_adddress); Write_adddress = ((Uint32)0x00000001 << 8) | Write_Socket_OPCODE; IINCHIP_WRITE_add_data(Write_adddress , Sn_CR); Write_adddress = ((Uint32)0x00000001 << 8) | Write_Socket_OPCODE; IINCHIP_WRITE_add_data(Write_adddress , Sn_CR); Read_adddress = ((Uint32)(0x00000003) << 8) | Read_Socket_OPCODE; // check port is init or not IINCHIP_READ_add_data(Read_adddress); Read_adddress = ((Uint32)Base_address << 8) | Read_Socket_OPCODE; // 0x00 is the control phase bit sets IINCHIP_READ_Buf_data(Read_adddress,&read_socket_data[0],10); // Read_adddress = ((Uint32)PHY_address << 8) | 0X01; // IINCHIP_READ_add_data(Read_adddress); // // Read_adddress = ((Uint32)Base_address << 8) | 0X01; // IINCHIP_READ_add_data(Read_adddress); } Thank in advance.

Akash Ahirwar · Answer

when i setting Sn_CR for OPEN Socket and check Sn_SR status it is showing me 0x00 it means it is not set. please resolve my problem

Akash Ahirwar · Answer

for me now after listening command (SOCK_LISTEN) I’m not getting SOCK_ESTABLISHED condition true. when i try to connect the putty application. please help me for the solutions. I’m attaching the wire Shark screen shorts.