Wiznet makers

Sushma_WIZnet

Published September 22, 2022 ©

9 Projects

1 Resellers

0 Contests

Original Link

[AIoT] Smart Desk using WIZnet EVB-Pico and TinyML

When the IR sensors detect a human is sitting on the desk, it will turn on charger, monitor and other devices connected to the Relay Module.

COMPONENTS Hardware components

x 1

Software Apps and online services

Arduino - Arduino IDE

x 1


PROJECT DESCRIPTION

Introduction

There is a huge wastage of energy in our daily life, which can be saved if we turn off the devices when not in use. Unfortunately we humans are so busy that we forget to turn them off. So to solve this problem, we thought of making all the electrical components smart. Initially we started with making our work desk smart. For this we placed an IR sensor on the desk which will detect if anyone is sitting on the desk, and toggle its output. The IR sensor is connected to a microcontroller which controls the Relays based on the output of the IR sensor.

Components

Hardware Component

  • W5100S-EVB-Pico
  •  
  •  
  •  IR Sensor Module FC-51
  •  
  •  
  •  4ch Relay

 

 

Software Component

 Arduino IDE

IR SensorIR sensor is an electronic device that emits light in order to sense some object of the surroundings. An IR sensor can measure the heat of an object as well as detect the motion. Usually, in the infrared spectrum, all the objects radiate some form of thermal radiation.

  • IR SensorIR sensor is an electronic device that emits light in order to sense some object of the surroundings. An IR sensor can measure the heat of an object as well as detect the motion. Usually, in the infrared spectrum, all the objects radiate some form of thermal radiation.

4ch RelaysA power relay module is an electrical switch that is operated by an electromagnet. The electromagnet is activated by a separate low-power signal from a microcontroller. When activated, the electromagnet pulls to either open or close an electrical circuit.

  • 4ch RelaysA power relay module is an electrical switch that is operated by an electromagnet. The electromagnet is activated by a separate low-power signal from a microcontroller. When activated, the electromagnet pulls to either open or close an electrical circuit.

W5100S-EVB-PicoWIZnet Pico is a microcontroller evaluation board based on the Raspberry Pi RP2040 and fully hardwired TCP/IP controller W5100S – and basically works the same as Raspberry Pi Pico board but with additional Ethernet via W5100S.

  • W5100S-EVB-PicoWIZnet Pico is a microcontroller evaluation board based on the Raspberry Pi RP2040 and fully hardwired TCP/IP controller W5100S – and basically works the same as Raspberry Pi Pico board but with additional Ethernet via W5100S.

Circuit Diagram

Explaination

The VCC & GND pins of Camera, IR sensor and 4ch Relay are connected to VCC and GND respectively. The IR sensor’s DOUT pin is connected to GP1 of the WIZnet Pico 2 and the output from WIZnet Pico 1 is connected to GP0 of the WIZnet Pico 2.

If the camera detects any human face, it will turn the GP0 of WIZnet Pico 2 to HIGH and when the IR sensor detects something it will turn the GP1 of WIZnet Pico 2 to LOW (refer to the link below for the human detection).

When the GP0 and GP1 of WIZnet Pico 2 are HIGH and LOW respectively, the Relays connected to GP2, GP3, GP4 and GP5 are turned HIGH ie when any human is detected by the camera and the he is sitting on his desk, the microcontroller will turn on the relays.

Youtube


 

Documents
  • Smart Desk using WIZnet EVB-Pico and TinyML

  • Circuit Diagram

Credits
Sushma_WIZnet

9 Projects

1 Resellers

0 Contests

Comments Write