--- title: "DFR0342 W5500 Ethernet with POE Main board" url: "https://maker.wiznet.io/mason/resellers/DFR0342-W5500-Ethernet-with-POE-Main-board/" markdown_url: "https://maker.wiznet.io/mason/resellers/DFR0342-W5500-Ethernet-with-POE-Main-board/md" type: "VAR: Value-Added Reseller Products" author: "mason" author_url: "https://maker.wiznet.io/mason/" original_author: "mason" published: "2020-09-14" language: "en" likes: 0 views: 682 comments: 0 source: "WIZnet Makers (https://maker.wiznet.io/)" --- # DFR0342 W5500 Ethernet with POE Main board > DFR0342 W5500 Ethernet with POE Main board Original author: mason ## Documents and links - [V2.0 Schematic](https://github.com/Arduinolibrary/DFRobot_W5500_Ethernet_POE_mainboard/raw/master/W5500%20V2.0%20Schematic.pdf) (schematics) ## Article ## Tutorial ### Preparation 1. Standard POE Protocol Ethernet Swtich X1 2. W5500 Ethernet with POE Mainboard X1 3. Micro USB cable X1 4. RJ45 network cable X2 ### Step 1 Connect W5500 Reset pins: Connect A-RST pin to D11. (Default: Connected) ![DFR0342_A-Rst.jpg](https://raw.githubusercontent.com/DFRobot/DFRobotMediaWikiImage/master/Image/DFR0342_A-Rst.jpg) ### Step 2 Plug one end of the ethernet cable to W5500 mainboard, another end to any LAN ports of the Ethernet Switch, or you can use normal Internet switch or router device to directly connect to a PC's network interface (the module needs to be powered up here). ![Connection 1](https://dfimg.dfrobot.com/nobody/wiki/c9d457db76cd43a362928f2e7765214e.png) ### Step 3 Connect the W5500 mainbord to a computer with a USB cable. ![Connection 2](https://dfimg.dfrobot.com/nobody/wiki/b0ff4111d0e550f4614f0e42e800e961.png) ### Step 4 Download the WIZnet official Arduino library?[here](https://github.com/Wiznet/WIZ_Ethernet_Library). Unpack the downloaded file and then, place the Ethernet file under Arduino IDE 1.0.x or Arduino IDE 1.5.x in the libraries file of Arduino IDE according to your Arduino IDE version (overlap the original Ethernet library). Open Arduino IDE editor, find WebServer example in File->Example->Ethernet and open it. 1. Download the W5500 Ethernet library?[here](https://github.com/Wiznet/WIZ_Ethernet_Library) 2. Replace the existing Ethernet library according to your Arduino IDE version: ![Arduino IDE 1.0.X](https://raw.githubusercontent.com/DFRobot/DFRobotMediaWikiImage/master/Image/DFR0342_IDE_1.0.x.png)?![Arduino IDE 1.5.X](https://raw.githubusercontent.com/DFRobot/DFRobotMediaWikiImage/master/Image/DFR0342_IDE_1.5.x.png) **NOTE**: Good news! You can use arduino IDE v1.7 from Arduino.org that has "Ethernet 2" library, which works with this board. It means you don't have to download any modded libraries. Thank for the Vladimir Akopyan comments. Welcome to share your projects and comments on the Disqus. ### Step 5: Pin Definitions **Note: These parts should be declared at the beginning of the sketch.** 1. Define W5500 SPI “SS” pin and “Reset” Pin: ``` #define SS 10U //D10----- SS #define RST 11U //D11----- Reset ``` 2. Setup function ``` void setup() { pinMode(SS, OUTPUT); pinMode(RST, OUTPUT); digitalWrite(SS, LOW); digitalWrite(RST,HIGH); //Reset delay(200); digitalWrite(RST,LOW); delay(200); digitalWrite(RST,HIGH); delay(200); //Wait W5500 ``` ### Example Open Arduino IDE, Select Boards -->Arduino Leonardo and COM port ```cpp /* Web Server A simple web server that shows the value of the analog input pins. using an Arduino Wiznet Ethernet shield. Circuit: * Ethernet shield attached to pins 10, 11, 12, 13 * Analog inputs attached to pins A0 through A5 (optional) created 18 Dec 2009 by David A. Mellis modified 9 Apr 2012 by Tom Igoe */ #include #include #define SS 10U //D10 ---- SS #define RST 11U //D11 -----Reset // Enter a MAC address and IP address for your controller below. // The IP address will be dependent on your local network: byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; IPAddress ip(192, 168, 1, 177); // Initialize the Ethernet server library // with the IP address and port you want to use // (port 80 is default for HTTP): EthernetServer server(80); void setup() { pinMode(SS, OUTPUT); pinMode(RST, OUTPUT); digitalWrite(SS, LOW); digitalWrite(RST, HIGH); //Reset delay(200); digitalWrite(RST, LOW); delay(200); digitalWrite(RST, HIGH); delay(200); //Wait W5500 //Open serial communications and wait for port to open : Serial.begin(9600); //while (!Serial) { // ; // wait for serial port to connect. Needed for Leonardo only //} delay(1000); // start the Ethernet connection and the server: Ethernet.begin(mac, ip); server.begin(); //Serial.print("server is at "); //Serial.println(Ethernet.localIP()); } void loop() { // listen for incoming clients EthernetClient client = server.available(); if (client) { //Serial.println("new client"); // an http request ends with a blank line boolean currentLineIsBlank = true; while (client.connected()) { if (client.available()) { char c = client.read(); Serial.write(c); // if you've gotten to the end of the line (received a newline // character) and the line is blank, the http request has ended, // so you can send a reply if (c == 'n' && currentLineIsBlank) { // send a standard http response header client.println("HTTP/1.1 200 OK"); client.println("Content-Type: text/html"); // the connection will be closed after completion of the response client.println("Connection: close"); client.println("Refresh: 5"); // refresh the page automatically every 5 sec client.println(); client.println(""); client.println(""); // output the value of each analog input pin for (int analogChannel = 0; analogChannel < 6; analogChannel++) { int sensorReading = analogRead(analogChannel); client.print("analog input "); client.print(analogChannel); client.print(" is "); client.print(sensorReading); client.println("
"); } client.println(""); break; } if (c == 'n') { // you're starting a new line currentLineIsBlank = true; } else if (c != 'r') { // you've gotten a character on the current line currentLineIsBlank = false; } } } // give the web browser time to receive the data delay(1); // close the connection: client.stop(); //Serial.println("client disconnected"); } } ``` Copy ### Check that it works Open the Arduino Serial Monitor to initialize the setup and you will see some information about the connection processing. Open your browser, input the IP address and you should get see data of 5 virtual analog pins: ![W5500IE](https://dfimg.dfrobot.com/nobody/wiki/b96b48610e7bba0ddeae4d0dc53a393b.jpg) --- Source: https://maker.wiznet.io/mason/resellers/DFR0342-W5500-Ethernet-with-POE-Main-board/